Installation of optek sensors at the inlet and outlet of a centrifuge can improve separation performance, reduce losses and improve product consistency.
Bronkhorst develops micro to low flow liquid metering instruments based on a thermal mass flow measuring principle.
The CENTRiCAL workshop calibration test bench is designed to combine ease of use, versatility and ergonomics for performing calibrations in a workshop.
The Noshok 20, 25 and 30 series of intelligent pressure and level transmitters is designed to address the specific requirements of the food and beverage industry.
EL-FLOW Select Series Mass Flow Meters/Controllers from Bronkhorst are thermal mass flow meters of modular construction with a 'laboratory style' pc-board housing.
London Electronics' range of general-purpose large displays have a simple yet rugged design that gives long-term reliability and a smart appearance.
Michell Instruments' QMA601 process moisture analysers provide moisture control over long periods without the need for frequent maintenance.
Katronic flowmeters are hygienic, quick to install, and easy to operate and maintain.
Michell Instruments has introduced a new version of its 2-wire Easidew dewpoint transmitter, with a simultaneous analog and digital Modbus RTU output and a rugged 5-pin M12 electrical connection.
Michell Instruments' QMA401 low-maintenance trace moisture analyser has a new look and enhanced usability.
The ST50 Mass Flow Meter Series from Fluid Components International (FCI) provides precision measurement of air to increase the efficiency of industrial air blowers and dryers used in raw materials production.
The Electro-Chemical Devices HCA1 Portable Colorimetric Chlorine Test Kit is suitable for testing free and total chlorine in drinking water, waste water, environmental waters, cooling towers and rinse waters in the food and beverage industry.
The FLT93 Flow Switch from Fluid Components International (FCI) provides an early warning alert to the potential of dry running conditions, cavitation and other pump issues that can lead to emergency shutdowns, service interruptions and unplanned maintenance.
The ECD FC80 is a panel-mounted, ready-to-use free chlorine analyser designed to monitor free chlorine in drinking water, rinse water, cooling water or other fresh water samples.
Beamex has introduced a free-of-charge, cloud-based calibration certificate generation software called LOGiCAL.
The rugged ST51 Series Thermal Mass Flow Meter from Fluid Components International (FCI) provides continuously accurate measurement of syngas fuel flow to the combined heat and power (CHP) engine.
The ECD Model X80 Universal Transmitter is a single- or dual-channel transmitter designed for the continuous measurement of pH, ORP, pION, dissolved oxygen, turbidity, conductivity or resistivity in a general-purpose industrial environment.
ECD's S80 sensors measure pH, ORP, pION, dissolved oxygen, turbidity, conductivity and resistivity in liquid processes.
The FLT93 Flow Switch Series from Fluid Components International (FCI) provides a solution for verifying chemicals or additives are being injected and ensuring injection pumps and feeders continue to operate.
The Triton TR6 infrared turbidity sensor measures turbidity or suspended solids in four selectable dual ranges, featuring preset low and high ranges from 0 to 4000 NTU.
The Michell Instruments XZR400 oxygen analyser is designed to measure trace levels of oxygen in pure, inert gases such as nitrogen, argon, helium and carbon dioxide.
The Electro-Chemical Devices T80-S80 analyser system is a modular plug-n-play system that simplifies operations and lowers total operating costs in aquaculture.
Electro-Chemical Devices' S10 and S17 Analytical pH Sensors monitor pH in water-based solutions and are sulfide-resistant.
The TC-80 Total Chlorine Analyser from Electro-Chemical Devices (ECD) monitors total chlorine in drinking water, rinse water, cooling water and other freshwater samples.
The rbr ecom-J2KN analyser utilises electrochemical sensors to measure exhaust emissions.
The ES20 compact sampling system from Michell Instruments now has the option of an Easidew PRO XP dewpoint transmitter.
Designed for industrial processes, manufacturing operations, pumps, compressed air, gas compressors and HVAC systems requiring flow assurance and alarming, the compact SIL 2 compliant FS10i Flow Switch/Monitor from Fluid Components International (FCI) features good performance and operation.
The CA-6 UV Family of Spectroscopic Analysers from Electro-Chemical Devices can monitor any two selected parameters in separate measurement ranges for ammonia, nitrate or chemical oxygen demand (COD 254 nm).
The HygroSmart HS3 interchangeable relative humidity and temperature probe is 100% configurable to allow maximum flexibility to the user. This gives users the ability to alter their RH and temperature measurements to keep step with changes or developments in their process.
The Vortab Elbow Flow Conditioner helps to eliminate the turbulent fluid flows that result in pump cavitation.
The Haze Control 4000 photometric converter has been designed for high-precision haze (turbidity) measurements.
Michell Instruments has launched an upgraded version of its HygroSmart I7000XP interchangeable relative humidity sensor.
Process Control’s UNIFLOW-200 MFC flow computer is suitable for a variety of flowing fluids and a range of flow meters.
Michell Instruments' XGA301 bench-mounted analyser can be configured to use either zirconia oxide or electrochemical cells to measure oxygen and/or infrared technology to measure other gases such as carbon dioxide, methane and carbon monoxide.
The ST98 air/gas flow meter from Fluid Components International allows facility engineers to monitor and control the precise amount of fuel needed to run HVAC boilers efficiently.
The Michell I7000 Hygrosmart Relative Humidity and Temperature sensor claims to provide highly reliable and accurate measurements of the key parameters for ensuring food is kept fresh and in good condition.
Fluid Components International's ST100 Thermal Mass Flow Meter is suitable for use in wastewater treatment plants for flow measurement in aeration basins. It is Profibus PA compatible, providing accuracy combined with digital bus communication flexibility.
The ST75 Air/Gas Flow Meter from Fluid Components International (FCI) measures fuel gas, process gas, inert gas, waste gases and air in small line sizes, and is suitable for optimising natural gas flow control for industrial ovens, heat chambers and furnaces.
The DryCheck is a stable dewpoint instrument that includes a built-in simple sampling system. Its compact size allows it to be installed in a number of dewpoint measurement applications, including plastic moulding machines and industrial gas manufacture.
The Interface 3AXX series load cells measure force in x, y and z directions and come in a wide range of capacities from 10 N to 50 kN.
Michell Instruments has extended its range of oxygen analysers with the introduction of the compact XZR200 oxygen analyser. It is easy to install and integrate into existing systems as no specialist software is required.
Noshok has added the 820/821 Series Digital Temperature Indicators to its temperature measurement solutions offering.
Michell Instruments’ DT722 series RH and temperature transmitters provide a solution to maintaining reliable RH measurements in harsh or corrosive environments.
Michell Instruments has released the XTP601 thermo-paramagnetic oxygen analyser to provide fast, accurate measurements of oxygen levels in various background gases.
The ST100 Series of thermal mass air/gas flow meters comprises two core model families: ST meters measure both mass flow and temperature, with the STP family also measuring pressure.
Noshok offers a variety of orifices and snubbers to protect instrumentation from pulsation and pressure spikes by restricting the flow of rapidly increasing and decreasing pressures.
Noshok 100 and 150 Series Mini Valves are small in size, but deliver serious strength and durability. Available in zinc nickel-plated steel, electropolished stainless steel and 360 brass, these valves have been designed for tough applications.
The Interface WMCP Overload Protected Stainless Steel Miniature Load Cell model adds overload protection to the WMC family features of environmentally sealed, stainless steel housings, proprietary temperature-compensated strain gauges and small load cell sizes for convenient mounting and machine integration.
The ST51 Air/Gas Flow Meter from Fluid Components International (FCI) provides industrial plant engineers with a solution for greenhouse gas (GHG) monitoring and supports the EPA’s BACT (Best Available Control Technology) initiative in the US. The flowmeter is suitable for the measurement and monitoring of industrial plant greenhouse gases. It features a no-moving-parts design that’s non clogging and operates over a wide flow range with low-flow sensitivity. Packaged in an explosion-proof transmitter, the calibration is matched to the user’s actual gas composition and installation conditions.
The Noshok 800 Series platinum resistance temperature transmitter is suitable for immediate, accurate temperature measurement in applications including water systems, storage tanks, industrial machinery and machine tools, HVAC systems and refrigeration systems.
Ronan’s X96SI/R radiometric transmitter is fully ethernet capable, enabling configurations, software updates and data logging to be completed easily through the user’s PC, using a standard web browser.
The Model FS10A flow switch/monitor from Fluid Components International (FCI) is a low-cost solution for continuously verifying flows within liquid or gas process analyser sampling systems. It is suitable for the continuous monitoring of analyser sample flows to provide the highest integrity process analysis without interruption.
Environmental, quality and plant managers responsible for reporting gas emissions from stacks and chimneys per European CEN or MCERT directives will find that the rugged MT91 multi-point gas mass flowmeter from Fluid Components International (FCI) offers an approved solution.
The VIP (Vortab Insertion Panel) flow conditioner can be used to neutralise flow profile irregularities caused by elbows, valves, blowers, compressors and other flow disturbances that commonly occur in piping and duct runs and cause flowmeter inaccuracies. It provides a swirl-free, symmetric and repeatable flow profile that flowmeters require for accurate measurement.
Food and beverage plants that require carbon dioxide or produce CO2 as a by-product will find the advanced ST75 Flow Meter from Fluid Components International (FCI) delivers precise direct mass flow measurement of gases in an easy-to-install, insertion-style instrument that requires almost no maintenance over a long life.
The Fluid Components International GF90 Gas Flow Meter provides accurate, reliable measurement in chlorinated water disinfection systems.
The Beamex POC6 is an accurate and user-friendly automatic pressure output controller, providing regulated output from vacuum to 70 bar (1015 psi). The POC6 can be delivered as panel mounted to Beamex MCS100 Workstation or as a portable desktop version. The POC6 can be used as a stand-alone pressure controller or as integrated to the Beamex calibration system.
The Fluid Components FlexSwitch FLT93S flow/level/temperature switch can be used in separation tanks and other vessels with mixed density media for accurate interface detection and control.